Rolling trays and boxes

Non-perforated tray LNMZT (M)

Material:
Sheet steel, hot-dip galvanized.
Steel grade :
08 PS
Degree of protection:
IP 00
Installation conditions:
for laying wires and cables with voltage up to 1000V when performing open electrical wiring and open laying of cable lines
Additionally:
Possibility of manufacturing a tray from steel up to 1 mm thick and painted.

Equipment
Code Index Size, mm Metal thickness, mm Weight, kg Useful cross-sectional area, cm 2 Package quantity, m
width height length
91050T LNMZT (M) - 50x50pr fifty fifty 2500 0.55 0.77 24.22 five
91100T LNMZT (M) - 100x50pr 100 fifty 2500 0.55 0.91 48.44 five
91180T LNMZT (M) -100x80pr 100 80 2500 one 2.11 77.42 five
91110T LNMZT (M) -100x100pr 100 100 2500 one 2.40 97.02 five
91200T LNMZT (M) -200x50pr 200 fifty 2500 0.7 1.77 98.44 five
91280T LNMZT (M) -200x80pr 200 80 2500 one 2.84 156.42 five
91210T LNMZT (M) -200x100pr 200 100 2500 one 3.14 196.02 five
91300T LNMZT (M) - 300x50pr 300 fifty 2500 one 2.32 147.44 five
91450T LNMZT (M) -400x50pr 400 fifty 2500 one 3.88 198.44 five
91480T LNMZT (M) -400x80pr 400 80 2500 one 10.6 314.56 five
91410T LNMZT (M) -400x100pr 400 100 2500 one 11.34 393.2 five
Perforated tray LPMZT (M)

Material:
Sheet steel, hot-dip galvanized.
Steel grade :
08 PS
Degree of protection:
IP 00
Installation conditions:
for laying wires and cables with voltage up to 1000V when performing open electrical wiring and open laying of cable lines
Additionally:
Possibility of manufacturing a tray from steel up to 1 mm thick and painted.
On request, it is possible to manufacture a rolling tray and a cover up to 6m long.

Equipment
Code Index Size, mm Metal thickness, mm Weight, kg Useful cross-sectional area, cm 2 Package quantity, m
width height length
90180T LPMZT (M) -100x80pr 100 100 2500 one 1.94 77.42 five
90110T LPMZT (M) -100x100pr 100 100 2500 one 2.21 97.02 five
90280T LPMZT (M) -200x80pr 200 80 2500 one 2.62 156.42 five
90210T LPMZT (M) -200x100pr 100 100 2500 one 2.88 196.02 five
90380T LPMZT (M) -300x80pr 300 80 2500 one 3.12 235.42 five
90310T LPMZT (M) -300x100pr 300 100 2500 one 3.34 295.02 five
90400T LPMZT (M) -400x50pr 400 fifty 2500 one 3.49 198.44 five
90410T LPMZT (M) -400x80pr 400 80 2500 one 9,7 314.56 five
90510 LPMZT (M) -400x100pr 400 100 2500 one 10.44 393.2 five
Covers for trays LNMZT (M) and LPMZT (M)

Material:
Sheet steel, hot-dip galvanized.
Steel grade:
08 PS
Method of manufacturing
rolled steel
Additionally, the
possibility of manufacturing a tray from steel up to 1 mm thick and painted

Code Index Metal thickness, mm Weight, kg Width, mm L1, mm Qty in a package
90051T KLZT (M) -50pr 0.55 0.25 fifty 2500 fifty
90101T KLZT (M) -100pr 0.55 0.44 100 2500 thirty
90201T KLZT (M) -200pr 0.7 1.14 200 2500 twenty
90301T KLZT (M) -300pr 0.7 1.65 300 2500 fifteen
90401T KLZT (M) -400pr 1.0 2.25 400 2000 five
Trays - boxes series НСТ

OSTEC trays-boxes of the НСТ series are made of steel pre-galvanized in continuous galvanizing units according to the Sendzimir method. Perforated and non-perforated trays-boxes of the NST series are made of metal with a thickness of 1 mm, 1.2 mm, 1.5 mm and 2 mm. NST series trays-boxes are completed with corners and accessories.

Non-perforated tray, НСТ series Perforated tray НСТ series
Name Width (from – to) Height (from – to) Length Thickness
LNMZT (NST) 50 - 600 50 - 200 3000 1.2-2 mm
LPMZT (NST) 50 - 600 50 - 200 3000 1.2-2 mm
KLZT (NST) cover for trays of NST series 50 - 600 fifteen 3000 1 mm
Methods for connecting trays
Connection of trays "daddy-mama" with each other
1. Joining trays (1) are overlapped (“male-female”).

2. The trays are connected by three screw sets in the following sequence:
Screw (3) - from the inside of the tray, Nut (2) - from the outside, from the side of the tray.
Hardware used for assembly: Screw (3) - М6х10 (3 pcs.); Nut (2) - M6 with locking collar (3 pcs.).
Connecting trays using a connector (SLB)
1. Joining trays (2) are joined flush.

2. The joint is clasped from below with a connector (1).

3. The connector (1) is fixed to the trays (2) with 8 screw sets through the perforations located along the sides of the tray (2): the screw (3) - from the inside, from the side of the tray (2), the nut (4) - from the outside, from the side of the connector (1).
Hardware used for assembly: Screw (3) - М6х10 (8 pcs.); Nut (4) - M6 with locking collar (8 pcs.).
Tray and corner (pivot) connection
1.The mating tray (2) and corner (1) are butted together.

2.The connecting strip (3) is attached from the inside to the side walls of the adjacent elements of the track (in this case, the tray-corner) by 3 screw sets through the perforations located on the side walls, in the following sequence:
screw (4) - from the side of the strip ( 3), nut (5) - outside, from the side of the tray / corner.
Two screw sets for connecting the bar (3) and the tray (2), one screw set for connecting the bar (3) and corner (1).

3.On the joint, 2 connecting strips are used.

The connection principle is the same for all angles (turns).
Hardware used for assembly: Screw (3) - M6x10 with a wide head (6 pcs.); Nut (4) - M6 with locking collar (6 pcs.).
Tray to Branch Connection (OGP)
1. Cut a hole in the tray (part of the side and bottom) 16 mm in depth and with a length corresponding to the length of the coupler (1).
the coupler (1) is inserted inside the tray (2) until the sides of the tray (2) and the coupler (1) match.

2. The connecting strip is fastened from the inside to the side walls of the adjacent elements of the track (in this case, the branch tray
) with 3 screw sets through the perforations located on the side walls
in the following sequence: screw (4) - from the side of the strip (3), nut (5) - outside, from the side of the tray / branch.
two screw sets for the connection of the bracket (3) and the tray (2), one screw set for the connection of the bracket (3)
and the branch (1).

3. Two connecting strips are used for the joint. The connection principle is the same for all versions of the Taps.
Hardware used for assembly: Screw (3) - M6x10 (6 pcs); Nut (4) - M6 with locking collar (6 pcs).
Connecting Tray Cover and Branch Cover (COG)
In the cover of the tray (2) a hole is cut 50 mm deep and long corresponding to the length of the cover.